Qi Green Lantern Charger

我想拥有一个绿色灯笼电量，有很长一段时间。可悲的是，原始的直流收藏品是可笑的昂贵。经过一点研究，我决定建立自己的。而不是只是刷新他们的功能，我决定使它成为手机充电器的实际可用。

您可以简单地将手机放在上面，它将被加载。唯一的要求是您的手机可以与Qi收取（请退房维基百科should you want to learn more about Qi). But don’t worry if your phone doesn’t come with Qi, there arecheap adapters您可以使用（如您在图片中看到，我也必须使用一个）。

电力电池的另一个功能是您可以使用环形亮起。

“在最明亮的一天，在最沮丧的夜晚，

No evil shall escape my sight.

Let those who worship evil's might

谨防我的力量 - 绿色灯笼的光！“

正如您在图片中看到的那样，背部还有三个额外的USB插头来充电多个手机。

Please check out这个链接您是否不知道电源电池是什么。长话短说，他们用来为绿灯灯充电。顺便问一下，你应该不喜欢绿色，有很多不同versions。

我设计了一切Fusion 360。大部分设计都很简单，可以通过旋转和挤出草图来完成。

The only thing that I found tricky to do was to make the small indent that goes all around the middle part. Luckily Fusion 360 has an awesome feature helping you to do so.

Simply make a sketch in the middle, like the one shown in the first picture. Afterward close it and open a new sketch. Select "Project/Include" and then select "Intersection Curve". You will have to select one line/curve at a time, but as you can see it works really well.

之后，您必须打开一个新的草图并绘制您想要减去的结构，如第五图片所示。确保选择右侧。现在剩下的所有这些都是选择“创建”，“扫描”，然后是结构，以及路径。

You can play around and download my design here:

http://a360.co/2u2bilj.

我决定将顶部设计为两部分，这样就可以在没有任何支持结构的情况下打印它。只需将徽标板粘在一起即可。确保将它们对齐。

I printed all the parts as a “fast print” on my Ultimaker, because I was impatient and I knew that after priming and sanding it would look smooth anyway.

从底部断开支撑结构时要小心，因为USB插头之间的墙壁相当小。

Next print the middle part. I went through a few design iterations concerning the lenses and went with the ones I uploaded to this step.

由于我是一个完美主义者，我决定给电机电池平稳而有光泽。我使用了三层薄薄的底漆并打磨一切。在另一块薄薄的底漆之后，我用绿色的涂料和光泽的饰面。

The lens is printed with PET filament, 100% infill and a high layer resolution.

我决定添加磁铁以连接顶部和底部，即使它们不需要，因为一切都很适合。

Put the lenses through the bottom or top hole and carefully push them in place.

I used这个由AUKEY充电器。老实说主要意图on for my decision to use it was that it has green USB plugs.

It turned out that it was difficult to take apart and I had to carefully use a chisel.

之后，我将USB插头和电源插头取消亮，并将其焊接回到适当位置，如图片所示。别忘了将电源插头电缆放在底部的孔中。我在零件背面使用了一个强大的两个组件胶水，以保持一切到位

I used这个QI充电器的项目。您可以简单地将其拧紧并使用一些热胶将其固定在顶部。使用一些磁带防止电线妨碍光线。

As a light I used这个廉价营地灯泡。拆开也很简单。我希望用戒指激活电力电池的光。因此，我决定添加一个簧片开关。只需将其连接并将其粘合到我设计的插槽中。

打印安装器I附加到该步骤，将灯电路板胶水到它并连接所有导线。如图所示。

You can find my design of the ring here:

http://a360.co/2t7bzI8

Please feel free to adapt it so that it fits your finger. Simply glue a 8x2 mm magnet into it, prime and paint it.

It took me a while to get the handle right. At first I tried bending a piece of wire, but it looked horrible (also the paint didn't stick to the aluminum wire I got).

So I went to my local hardware store and picked up a cheap ($2) hand net for kids and was quite happy with the result. Simply print the two small adapter pieces, bend the ends of the wire and attach them.

喷涂手柄并将其推入电池的孔中。

恭喜你完成了。